Olimex

* MCU: MSP430F413 with 8K Bytes Program Flash, 256 Bytes data Flash, 256 Bytes RAM * JTAG connector * Custom LCD panel with 5 digits, 5 decimal counters, special signs * RS232 connector * RS232 interface circuit with Tx, Rx signals * Dallas touch button port * status LED * two buttons * Buzzer * CR2032 li-battery holder 3V * 32 768 Hz oscillator crystal * TEST pin pull-down * RST/NMI pin pull-up * power supply filtering capacitor * extension headers for unused uC pins * PCB: FR-4, 1.5 mm (0,062"), green soldermask, white silkscreen component print * Dimensions: 80x50 mm (3.15x1.96") Learn More

* MCU: AT91SAM7S256 16/32 bit ARM7TDMI™ with 256K Bytes Program Flash, 64K Bytes RAM, USB 2.0, RTT, 10 bit ADC 384 ksps, 2x UARTs, TWI (I2C), SPI, 3x 32bit TIMERS, 4x PWM, SSC, WDT, PDC (DMA) for all peripherals, up to 60MHz operation * standard JTAG connector with ARM 2x10 pin layout for programming/debugging with ARM-JTAG * USB connector * Two channel RS232 interface and drivers * SD/MMC card connector * two buttons * trimpot connected to ADC * thermistor connected to ADC * two status LEDs * on board voltage regulator 3.3V with up to 800mA current * single power supply: 6V AC or DC required * power supply LED * power supply filtering capacitor * RESET circuit * RESET button * 18.432 Mhz crystal on socket * extension headers for all uC ports * PCB: FR-4, 1.5 mm (0,062"), soldermask, silkscreen component print * Dimensions: 120 x 80 mm (4.7 x 3.15") Learn More

Parallel port JTAG dongle interface, can be used with all ARM devices for programming and debugging. Learn More

ARM-JTAG-EW is fast and reliable JTAG programmer / debugger designed to work with EW-ARM. It supports fast USB JTAG and is compatible with Embedded Workbench. It has features available only in the expensive Logic analyzers and offer to the user not only software breakpoints, but also hardware breakpoints - user can stop the code by external triggers which may be the target power consumption, rising/falling edge external signals, analogue signal window value. ARM-JTAG-EW emulates on low level the IAR Systems' J-LINK API so it works like normal J-LINK debugger, but add some unique features which are available only in the very high end and expensive debugger tools on the market. Learn More

Three-in-one USB JTAG debugger - offers JTAG + RS232 (full modem signals supported) port + power supply all in one compact device Learn More

High speed USB 2.0 JTAG dongle interface, can be used with all ARM devices supported by OpenOCD for programming and debugging. Also includes a USB-to-serial converter for convenience. Learn More

Debug all ARM microcontrollers supported by OpenOCD Learn More

High speed USB 2.0 with lower lattency time, RTCK adaptive JTAG clock up to 30Mhz and higher throughput. Debug all ARM cores supported by OpenOCD. Learn More

AVR-CAN is inexpensive way to learn AT90CAN128 microcontroller from Atmel. It's in very compact form 60x55mm and the presence of both CAN and RS232 allow the customer to make bridge between UART and CAN networks. All AVR pins are available on extension connectors and the board can be easy snap-on prototype or other mother board where additional circuits are built. Learn More

AVR-GSM is excellent board for adding remote monitoring and control in remote places by GSM cellular network. Do you want to switch on/off your local heating in your mountain house? To monitor the temperature at up to 8 remote points up to 30 meters away from the module? To listen what happens in your house with silent call after you get message for alarm status? Then AVR-GSM is the board for you! It contains ATmega32 microcontroller and 3-band GSM GPRS module 900/1800/1900Mhz inside which covers most used GSM networks around the world. The GSM antenna is build in the board so no need for external expensive GSM antennas. AVR-GSM have two relays 240VAC/10A, two optoisolated inputs which could be connected to alarm sensors or just buttons for user actions (like call pre-loaded phone numbers), on-board temperature sensor and connector for additional up to 8 addressable remote temperature sensors at up to 30 meter distance from the module. Normal phone hook can be connected to this board and to allow user to speak, listen, taking and placing phone calls as normal stand alone cellular phone. AVR-GSM can be connected to PC with the USB connector it have and it is recognized as modem which could be used to add internet via GPRS to your computer (imagine how useful is this for your mountain house if there is no internet but only cellular network!). Learn More

AVR-H128 is inexpensive way to develop and prototype circuits with ATMEGA128 microcontroller without need to deal with SMD soldering. All microcontroller pins are available on extension header with 0.1" and power supply, oscillators, ICSP, JTAG are wired, so all you need to do is to connect your additional components to the AVR ports, as the step is 0.1" these headers perfectly fit the prototype sea of pad boards with 0.1" step. Learn More

AVR-H128CAN is inexpensive way to develop and prototype circuits with AT90CAN128 without need to deal with SMD soldering. All microcontroller pins are available on extension header with 0.1" and power supply, oscillators, ICSP, JTAG are wired, so all you need to do is to connect your additional components to the AVR ports, as the step is 0.1" these headers perfectly fit the prototype sea of pad boards with 0.1" step. Learn More

AVR-HX128A1 is inexpensive way to develop and prototype circuits with ATxMEGA128A1 microcontroller without need to deal with SMD soldering. All microcontroller pins are available on extension header with 0.1" and power supply, oscillators, ICSP, JTAG are wired, so all you need to do is to connect your additional components to the AVR ports, as the step is 0.1" these headers perfectly fit the prototype sea of pad boards with 0.1" step. Learn More

AVR-ICSP is cross connection cable which allow programmers with 6 or 10 pin connectors to be use with target boards with 6 or 10 pin connectors. Learn More

* ICSP 5x2 pin connector for in-circuit programming with AVR-PG1 or AVR-PG2 * DIL20 microcontroller socket * status LED connected to PB4 * reset IC ZM33064 * Quartz crystall oscilator circuit 10MHz * Voltage regulator +5V, 7805 and filtering capacitors * Power plug-in jack * RS232 DB9 female connector , simple level shifter with transistors and diodes * 4 optocoupler isolated inputs with screw terminals * input status LEDs * 4 relay outputs with 5A/250VAC contacts with screw terminals * output status LEDs * four mounting holes 3.3 mm (0.13") * FR-4, 1.5 mm (0.062"), green soldermask, white silkscreen component print * dimensions 80x100 mm (3.9 x 3.15") Learn More

AVR-IO-M16 is small but powerful board, perfect for small automation projects. The board have four Relays with 10A/250VAC current switching capabilities, four opto isolated digital inputs and RS232 port. One of our demo software show how easy is to control the inputs and output by PC compuer through the RS232 port. Learn More

AVR-ISP500 is fast and reliable USB AVR programmer, working directly with AVR Studio. It si recognized as STK500 programmer and programs all AVRs. As it used USB CDC no need for drivers and works under Windows, Linux and MacOS. If you do not want to use AVRStudio you can use AVR-ISP500 with AVR Dude. Learn More

AVR-ISP500-ISO is professional, fast and reliable USB AVR programmer. It have two modes of work: STK500 compatible USB programmer and USB Mass storage. In STK500 mode it working directly with AVR Studio. It is recognized as STK500 programmer and programs all AVRs. If you do not want to use AVRStudio you can use AVR-ISP500 with AVR Dude. In Mass Storage mode it created new drive on your computer and when you drag and drop the HEX file to this drive it program it in the target AVR attached to the ICSP connector. This is totally platform independant and works on any computer with USB host without need for any additional software. AVR-ISP500-ISO have internal flash of 2MB and can log AVRStudio communication and then reply it with single button push. This means once you load the code in the internal flash you can program quickly many targets with single button press. AVR-ISP500-ISO is galvano isolated from the target with 1000VDC isolation, this means you can use it with targets working on high voltage without risk to damage your computer. Learn More

AVR-ISP500-TINY is fast and reliable USB AVR programmer. It have two modes of work: STK500 compatible USB programmer and USB Mass storage. In STK500 mode it working directly with AVR Studio. It is recognized as STK500 programmer and programs all AVRs. As it used USB CDC no need for drivers and works under Windows, Linux and MacOS. If you do not want to use AVRStudio you can use AVR-ISP500 with AVR Dude. In Mass Storage mode it created new drive on your computer and when you drag and drop the HEX file to this drive it program it in the target AVR attached to the ICSP connector. This is totally platform independant and works on any computer without need for any software. AVR-ISP500-TINY have internal flash of 2MB and can log AVRStudio communication and then reply it with single button push. This means once you load the code in the internal flash you can program quickly many targets with single button press Learn More